Independent guide. Not affiliated with, endorsed by, or sponsored by Cricut. Cricut is named only to describe machines and materials.

Updated November 18, 2026

Cricut Maker 3 basswood settings

Maker 3 basswood at 1/16 in is pressure 750 and 14X passes. The 1/32 in row is 381 and 18X. Both use the Knife Blade. Explore 3 has no basswood row.

On Maker 3, 1/16 inch (1.6 mm) basswood is cut pressure 750, multi-cut 14X, Knife Blade. The 1/32 inch row is pressure 381 and multi-cut 18X, also Knife Blade. No mirror. Explore 3 and Joy do not publish a basswood row.

Published presets

These rows are for Cricut Maker 3 only. Leave pressure on Default, which is the published cut pressure. Mirror: no. Mat: Cricut’s mat chart does not name basswood. Heavy sheets such as chipboard are on StrongGrip. Use the mat Design Space prompts, and move the star wheels aside.

Design Space preset

Basswood - 1/16" (1.6 mm)

Cut pressure 750

Blade
Knife Blade
Multi-cut
14X
Pressure control
Start on Default
Less Default · 750 More

This is a Knife Blade preset. Use the published pressure and the published multi-cut. Cricut’s custom-pressure editor is documented for fine-point blades, not as a substitute for this row. The number is Cricut’s Cut Pressure column. It is not pounds or PSI. Copied November 18, 2026 from Cricut’s material list.

Design Space preset

Basswood - 1/32" (0.8 mm)

Cut pressure 381

Blade
Knife Blade
Multi-cut
18X
Pressure control
Start on Default
Less Default · 381 More

This is a Knife Blade preset. Use the published pressure and the published multi-cut. Cricut’s custom-pressure editor is documented for fine-point blades, not as a substitute for this row. The number is Cricut’s Cut Pressure column. It is not pounds or PSI. Copied November 18, 2026 from Cricut’s material list.

Test cut. Cut a small shape on a scrap of the same material before the real project. Cricut says results vary. If the scrap does not cut through, try More, or the next heavier preset that this machine actually publishes. If the blade cuts the mat, try Less. Do not copy a pressure from a different machine.

Basswood on Maker 3 is a Knife Blade project. It is slow on purpose. The multi-cut number is how many times the knife repeats the same path.

Match the thickness

The original Maker uses the same pressures. Its pass counts are written 14x and 18x. Explore 3 has neither row. Balsa is not basswood.

Knife Blade setup

Install the Knife Blade in the drive housing, not the fine-point housing. Cricut says to leave the plastic gear cover on, and to slide the star wheels to the side so they do not dent the wood. Designs should stay moderately simple. The knife article describes moderate detail, not lace.

Do not mirror.

Mat

The grip chart’s heavyweight mat is StrongGrip, and it names chipboard rather than basswood. Secure the sheet so it cannot creep during a dozen passes. A shifted mat ruins the cut partway through, and you cannot resume a half-cut path from a guess.

If it does not finish

Let the published pass count finish before you judge it. Stopping at pass 4 of 14 looks like “not cutting through.” If the knife still has not released the shape at the end, do a smaller test before you edit the pressure. Cricut’s custom-pressure screen is documented for fine-point blades. This preset is not one of those. A dull Knife Blade is a replaceable part. Forcing the fine-point blade “just to try” is how mats get carved.

See also the Cricut Maker 3 page and the material page.

Sources

Official rows were checked on November 18, 2026. Cricut can change a preset after that date. Open the article before a project you cannot spare.

Questions