Independent guide. Not affiliated with, endorsed by, or sponsored by Cricut. Cricut is named only to describe machines and materials.

Updated November 18, 2026

Cricut Joy glitter iron-on settings

Joy presets for Smart Iron-On glitter and sheet Glitter Iron-On, with mirror, mat, pressure, and a test cut. Numbers are from Cricut’s Joy tab.

On a Cricut Joy, Smart Iron-On glitter is preset “Smart Iron-On - Glitter,” cut pressure 147, multi-cut Off, Cricut Joy Fine-Point blade, no mat, mirrored. Sheet Glitter Iron-On is pressure 180, multi-cut Off, on a StandardGrip mat, also mirrored. Leave pressure on Default and test a scrap.

Published presets

These rows are for Cricut Joy only. Leave pressure on Default, which is the published cut pressure. Mirror: yes. Mat: Smart glitter loads with no mat if the piece is at least 4 inches long. Sheet Glitter Iron-On goes on a StandardGrip mat, shiny liner down.

Design Space preset

Smart Iron-On - Glitter

Cut pressure 147

Blade
Cricut Joy Fine-Point
Multi-cut
Off
Pressure control
Start on Default
Less Default · 147 More

Default is this published cut pressure. More and Less are the on-screen adjustments if a test cut is off. For a fine-point blade, Custom Materials can also edit the number. The number is Cricut’s Cut Pressure column. It is not pounds or PSI. Copied November 18, 2026 from Cricut’s material list.

Design Space preset

Glitter Iron-On

Cut pressure 180

Blade
Cricut Joy Fine-Point
Multi-cut
Off
Pressure control
Start on Default
Less Default · 180 More

Default is this published cut pressure. More and Less are the on-screen adjustments if a test cut is off. For a fine-point blade, Custom Materials can also edit the number. The number is Cricut’s Cut Pressure column. It is not pounds or PSI. Copied November 18, 2026 from Cricut’s material list.

Test cut. Cut a small shape on a scrap of the same material before the real project. Cricut says results vary. If the scrap does not cut through, try More, or the next heavier preset that this machine actually publishes. If the blade cuts the mat, try Less. Do not copy a pressure from a different machine.

Read the roll before you open Design Space. If it says Smart Iron-On and glitter, search Smart Iron-On - Glitter. If it is a sheet of Glitter Iron-On, search Glitter Iron-On. Cricut’s Smart Materials article tells you to pick the Smart row that matches the finish. The two Joy pressures are 147 and 180. Explore 3’s glitter numbers are different. Do not type those in.

Blade

Use the Cricut Joy blade in the silver and white housing, or the Premium Fine-Point Cutting Tool Cricut lists for Joy. The material tab calls the blade type “Cricut Joy Fine-Point.” An Explore housing will not fit.

Mat or matless

Smart glitter goes in with no mat when the piece is at least 4 inches long. Feed it straight, under the guides, until the rollers take it. Joy keeps about 1 inch above the design and 0.5 inch below it. Do not trim the roll first.

Sheet glitter iron-on uses a mat. Cricut’s mat chart puts iron-on on StandardGrip. The specialty iron-on page says shiny liner side down.

Mirror, weed, and press

Turn Mirror on. Weed the extra film and leave the letters on the liner. Glitter sheds, so weed on a surface you can wipe.

Cricut says to press from the Heat Guide, and to choose the Smart Iron-On material there if that is what you cut, because the liner is thicker. The specialty page’s household-iron fallback is cotton/linen, steam off, a 10–15 second preheat, 25–30 seconds of medium pressure, the same on the back, and a cool peel.

If it tears or does not cut

Not cutting through usually means the wrong preset, a dull blade, or a cut that needs More after a test. Tearing the design usually means too much pressure or a design with tiny serifs. Try Less, or simplify the letters. Do not switch on a multi-cut. Both official rows say Off.

See also the Cricut Joy page and the material page.

Sources

Official rows were checked on November 18, 2026. Cricut can change a preset after that date. Open the article before a project you cannot spare.

Questions