Updated November 18, 2026
Cricut Explore 3
What Explore 3 can cut, which blades fit, and how Smart Materials load without a mat. Knife Blade materials are not on its list.
Affiliate links. Shop links on this page are marked for sponsors. If you buy through one, we may earn a commission. You do not pay extra. Disclosure.
Size, mat, and Smart Materials
| Machine size | Height 5.91 in (15.01 cm), length 22.17 in (56.31 cm), width 7.01 in (17.80 cm). Cricut prints these figures for Explore machines as a group. |
|---|---|
| Weight | 10.98 lb (4.98 kg), from the same Explore size note |
| Smart Material width | Rolls are 13 in wide. The widest cut Cricut states is 11.7 in (29.7 cm). |
| Smart Material length | Up to 12 ft (3.6 m) for a single image or repeated cuts on compatible Smart Materials |
| Mats | 12 in × 12 in and 12 in × 24 in, in four grip strengths, plus the Card Mat 2×2 |
| Shortest matless piece | At least 6 in long, and Cricut’s tip says you need about 13 in × 6 in to cut without a mat |
| Thickness note on the material list | Explore 3 and Explore 4 say to stay under 2.0 mm, and that density matters, not thickness alone |
| Smart Materials | Yes. Long enough pieces load without a mat. |
Blades and tools named for this machine
- Fine-Point Blade and Housing. The blade Explore 3 ships with. Most vinyl, iron-on, paper, and sticker presets on the Explore 3 tab name this blade.
- Deep-Point Blade and Housing. Cricut’s blade guide says the 60-degree deep-point blade fits every Explore and Maker, and recommends it for thicker materials such as chipboard, magnet, and foam. A specific preset can still name the fine-point blade. Follow the preset.
- Bonded-Fabric Blade. Named on the Explore 3 material list for some bonded fabrics, including bonded denim. It is not the blade for vinyl or cardstock.
Explore 3 is a 12-inch class machine that also takes Smart Materials without a mat. Cricut’s comparison page describes Smart Vinyl and Smart Iron-On cuts up to 12 feet long. The quick start says the roll is 13 inches wide and the widest cut is 11.7 inches.
The material list for “Cricut Explore 3 & Cricut Explore 4” is one shared tab. A preset on that tab is the published setting for both, until Cricut splits the tab. This page was checked while they were still together.
Explore 3 does not cut the Knife Blade materials. If you need 1.5 mm chipboard or basswood, the published rows are on Maker and Maker 3, with the Knife Blade. Explore 3 does publish Light Chipboard at 0.37 mm, on the fine-point blade.
There is no dial. Connect the machine, choose Browse All Materials, and search the preset name. Cricut’s help says to test a scrap first.
Shop link, if you are comparing models: Cricut’s machine comparison.
Design Space presets copied for this site
Cricut publishes the full preset list on the material settings article, in this machine’s tab. The rows below are the ones copied on November 18, 2026. A material missing from this short table may still have a row in the article.
| Preset | Cut pressure | Multi-cut | Blade |
|---|---|---|---|
| Glitter Iron-On | 177 | Off | Fine-Point Blade |
| Smart Iron-On – Glitter | 163 | Off | Fine-Point Blade |
| Smart Vinyl – Permanent | 135 | Off | Fine-Point Blade |
| Premium Vinyl - Permanent Glossy | 115 | Off | Fine-Point Blade |
| Medium Cardstock - 80 lb (216 gsm) | 320 | Off | Fine-Point Blade |
| Cardstock (for intricate cuts) | 200 | 2x | Fine-Point Blade |
| Printable Sticker Paper, White (Green Liner Printing) | 70 | Off | Fine-Point Blade |
| Printable Sticker Paper, White (Gray Liner Printing) | 230 | Off | Fine-Point Blade |
| Printable Waterproof Sticker Set - White | 220 | Off | Fine-Point Blade |
| Light Chipboard - 0.37mm | 327 | 2x | Fine-Point Blade |
Setting pages
Sources
- Official Cricut Explore 3 Quick Start Guide
- Official All About Smart Materials
- Official All About Cricut Blades and Machine Tools
- Official All about Cricut Knife Blade
- Official Which materials can I cut with my Cricut smart cutting machine?
- Official How do I choose material settings?
- Official Cricut machine comparison
Questions
-
Does Explore 3 still have a Smart Set dial?
No. Cricut’s material-settings article says Explore 3 chooses the material in Design Space. The dial remains on Explore Air 2 and older. Turn that dial to Custom only on those older machines.
-
Can Explore 3 use a Knife Blade for basswood or thick chipboard?
No. Cricut’s Knife Blade article says the blade fits Maker machines only. Explore models do not have the drive, and they cannot be upgraded to add it. Basswood and 1.5 mm chipboard are not on the Explore 3 material tab.