Design Space preset
Printable Sticker Paper, White (Green Liner Printing)
Cut pressure 115
- Blade
- Fine-Point Blade
- Multi-cut
- Off
- Pressure control
- Start on Default
Independent guide. Not affiliated with, endorsed by, or sponsored by Cricut. Cricut is named only to describe machines and materials.
Updated November 18, 2026
Maker 3 has no “Laminated Printable Sticker Paper” row. Green-liner sticker paper is pressure 115. Kiss cut is the Sticker tool, not a separate pressure.
Maker 3 does not publish “Laminated Printable Sticker Paper.” That name, at pressure 250 and two passes, is on the Joy 2, Explore 5, and Maker 5 tabs. For Maker 3 white sticker paper, green liner is pressure 115 and gray liner is 265, multi-cut Off, fine-point blade. Choose Kiss Cut in the Sticker tool. Test a scrap.
These rows are for Cricut Maker 3 only. Leave pressure on Default, which is the published cut pressure. Mirror: no. Mat: LightGrip for printable sticker paper. Place the sheet in the direction Design Space shows.
Design Space preset
Cut pressure 115
Design Space preset
Cut pressure 265
Design Space preset
Cut pressure 170
A kiss cut on a Maker 3 is two choices, and only one of them is a material preset.
Cricut’s Sticker tool is the kiss-cut control. Select the artwork, choose Effects, then Sticker, then Kiss Cut. Kiss cut stops at the liner. Die cut goes through it. Cricut says you can set More or Less on the kiss-cut pressure menu and on the die-cut menu. Design Space does not remember that More or Less choice next time. The material you select is still the base pressure.
The tool’s compatible list is the Compatible tab in Design Space. Cricut names printable vinyl, sticker paper, and waterproof sticker sets as the materials it was built around.
White sticker paper, green liner: pressure 115, multi-cut Off, fine-point blade.
White sticker paper, gray liner: pressure 265, multi-cut Off, fine-point blade. The older sheet is thicker. Cricut’s sticker article says so, and the pressure jump matches that.
Printable Waterproof Sticker Set - White: pressure 170, multi-cut Off. The product instructions say to print, add the laminating sheet, put it on a LightGrip mat, and pick the set’s own material. That is the official laminated product for this machine. It is not “any laminate from a home roll.”
On Joy 2, Explore 5, and Maker 5, Cricut publishes Laminated Printable Sticker Paper, White at cut pressure 250 and multi-cut 2x. The Maker 3 and Maker 4 tab checked the same day does not include that name. Using 250 on a Maker 3 is a custom experiment. If you do it, Cricut’s custom-material help says to start from the closest listed material, test several times, and stay inside the machine’s thickness note (under 2.4 mm for Maker 3, and density still matters). This site will not print 250 as the Maker 3 answer.
Inkjet only. Laser printers can damage the sheet or the printer, per Cricut’s sticker article. LightGrip mat. Match the on-screen rotation. No mirror. No transfer tape. Peel each sticker off the liner by hand.
Cutting the liner means the kiss was too deep. Use Less on the kiss-cut menu, or confirm you did not pick Die Cut. Leaving a hinge of uncut film means More, or the wrong liner preset. A gray-liner pressure on a green sheet is a deep cut. A green-liner pressure on a gray sheet often fails to release.
Some makers who laminate their own sticker sheets tell you to search Design Space for “Sticker Paper” instead of inventing a pressure. That is one blogger’s workflow. It is not a row on Cricut’s Maker 3 tab, and it is not the 250 / 2x figure published for other machines. Laura Lambert, Kiss-Cut Stickers and Sticker Sheets with Cricut
See also the Cricut Maker 3 page and the material page.
There isn’t a published Maker 3 preset by that name, as of the November 18, 2026 check. Joy 2, Explore 5, and Maker 5 list Laminated Printable Sticker Paper, White at pressure 250 and multi-cut 2x. Do not enter 250 on a Maker 3 and call it official.
In Design Space, select the artwork, open Effects, and choose Sticker, then Kiss Cut. Cricut says a kiss cut goes through the printable layer and leaves the liner. Die Cut goes through both. Then pick the material that matches your sheet. Kiss and die each have a More or Less pressure menu.
Green printing on the liner means Printable Sticker Paper, White (Green Liner Printing), pressure 115, multi-cut Off. Gray printing means the gray-liner row, pressure 265. Cricut’s waterproof sticker set, which includes a laminating sheet, is a third row at 170.